Go Back   The AK Files Forums > General Forums > Gunsmithing & Build It Yourself

Notices

Reply
 
Thread Tools
Old 07-17-2017, 12:41 AM   #1
Lingwendil
The man that sold The World
 
Lingwendil's Avatar
 
AKaholic #: 177079
Join Date: Sep 2014
Location: Oakley, Ca.
Posts: 1,833
Default Hungarian AKM rebuild on recreator blank

So, a little back story. I've been involved in build parties off and on, helped build, demil, populate barrels, etc, but a couple years back I finally decided to build up my own kit. I ordered up a Hungarian AKM kit from AKbuilder, non-chrome barrel, everything but the trunnion matched numbers, it and came with polish furniture, and it was clearly an AK63D underfolder kit that was sold with a fixed stock and rear trunnion. Perfect kit for a no frills build, so I grabbed a Polish blank, migged in the lower rails, broke a dozen drill bits getting it finished, and did a full heat treat in a lady friend's kiln. Turned out great, if not a bit ugly. Scratches, scuffs, and even a little dent near the rear trunnion on the non-operator side, behind the screwed-on optics rail.



After a while I threw some plum furniture on it, and shot the shit out of it. It currently runs a naked gas tube and an AMD65 handguard.




However, after nearly 10,000 rounds, it's starting to look ratty. Especially after building up my Yugo M72, I feel like I'm comparing a Cadillac DeVille to a thrashed Honda Civic. I notice every single flaw, even if it functions flawlessly and is the most accurate AK I own.

So, I've decided it needs to get a nice receiver and a new proper optics rail. I ordered myself a fully hardened Hungarian receiver blank from recreator, and it is superb.





I stripped down the Hungarian, and went to work.








Got it demilled, and started test fitting, and everything fits perfectly. The one side of the trunnion looks to have a gap, but that's just from a burr that has since been removed.






Rigged up a nice easy way to get the holes drilled for the front trunnion. Works perfectly, I clamp the vice to the plate with a bigass C-clamp. Slide the receiver over the trunnion, drill, reposition, and drill again. Not pictured is the clamp I put around the receiver to keep it still. I slip a block under that side to keep it stable, and shim if necessary. Slip a drill bit in the holes that you've already drilled to keep it from walking around on you.






That's all I could get done today, I'll rough in the upper and lower rails soon. So far I am very happy to get this built up again, and these receivers are a joy to work with.
__________________
Don't sweat the petty things and don't pet the sweaty things.
Lingwendil is online now   Reply With Quote
Old 07-17-2017, 06:45 AM   #2
brawny
Veteran Member
 
AKaholic #: 187460
Join Date: Jun 2016
Location: New Orleans, LA
Posts: 1,857
Default

__________________
Be on the alert, stand firm in the faith, act like men, be strong.
Let all that you do be done in love.
1 Corinthians 16:13-14

Let not him who girds on his armor boast like him who takes it off.
King Ahab
brawny is online now   Reply With Quote
Old 07-17-2017, 09:15 AM   #3
Lane_H
Non-hispanic, Caucasian
 
Lane_H's Avatar
 
AKaholic #: 182543
Join Date: Oct 2015
Location: Ala-F'n-bama
Posts: 2,899
Default

I also need to do the same on my 1st build which coincidentally is also a ak63d kit with a fixed rear trunnion.

I am sure the 2nd go round on yours will turn out much nicer..

please ~Splain more bout that front trunnion rivet hole drill method?

hard to see in the pic / not quite sure what sorta clamp/vise is holding your trunnion that allows the receiver to slide into position for drilling.
??
__________________
Arguing with a man who has renounced his reason is like giving medicine to the dead.
Lane_H is online now   Reply With Quote
Old 07-17-2017, 09:59 AM   #4
Frog
Member
 
AKaholic #: 191877
Join Date: Mar 2017
Location: Bremerton, WA
Posts: 131
Default

Are you reusing the original barrel with 10k rounds through it? How is the bullet test on that bbl?
Frog is online now   Reply With Quote
Old 07-17-2017, 01:09 PM   #5
Lingwendil
The man that sold The World
 
Lingwendil's Avatar
 
AKaholic #: 177079
Join Date: Sep 2014
Location: Oakley, Ca.
Posts: 1,833
Default

Quote:
Originally Posted by Lane_H View Post

please ~Splain more bout that front trunnion rivet hole drill method?

hard to see in the pic / not quite sure what sorta clamp/vise is holding your trunnion that allows the receiver to slide into position for drilling.
??
I'll try and get some pics up, just waking up and have a one year old climbing all over me

Quote:
Originally Posted by Frog View Post
Are you reusing the original barrel with 10k rounds through it? How is the bullet test on that bbl?
Bullet test goes just fine! Heat will really accelerate wear, and since I'm not a rapid fire/mag dump sort of guy, the barrel is in excellent condition and is still very accurate. No sense swapping it out until It truly needs it. It may be a ho-hum non-chrome US-made barrel, but it just plain works, and works very well.
__________________
Don't sweat the petty things and don't pet the sweaty things.

Last edited by Lingwendil; 07-18-2017 at 02:20 AM.
Lingwendil is online now   Reply With Quote
Old 07-17-2017, 01:34 PM   #6
Frog
Member
 
AKaholic #: 191877
Join Date: Mar 2017
Location: Bremerton, WA
Posts: 131
Default

Wow thats impressive
Frog is online now   Reply With Quote
Old 07-17-2017, 04:50 PM   #7
timhogan427
I eat ar15's and shit out ak's
 
timhogan427's Avatar
 
AKaholic #: 178465
Join Date: Jan 2015
Location: morrow/cinci, ohio
Posts: 2,382
Default

are you following me? i finish an m72, then you finish an m72. i finish an original barrel hungarian ak, now you finish one. lol whats my nect project? looking good btw :-D
__________________
Living a lie, timmy!
timhogan427 is online now   Reply With Quote
Old 07-17-2017, 05:05 PM   #8
Lingwendil
The man that sold The World
 
Lingwendil's Avatar
 
AKaholic #: 177079
Join Date: Sep 2014
Location: Oakley, Ca.
Posts: 1,833
Default

Quote:
Originally Posted by timhogan427 View Post
are you following me? i finish an m72, then you finish an m72. i finish an original barrel hungarian ak, now you finish one. lol whats my nect project? looking good btw :-D
Maybe I'll do an AR with a steel lower next
__________________
Don't sweat the petty things and don't pet the sweaty things.
Lingwendil is online now   Reply With Quote
Old 07-17-2017, 06:24 PM   #9
timhogan427
I eat ar15's and shit out ak's
 
timhogan427's Avatar
 
AKaholic #: 178465
Join Date: Jan 2015
Location: morrow/cinci, ohio
Posts: 2,382
Default

damnit! lol
__________________
Living a lie, timmy!
timhogan427 is online now   Reply With Quote
Old 07-18-2017, 02:31 AM   #10
Lingwendil
The man that sold The World
 
Lingwendil's Avatar
 
AKaholic #: 177079
Join Date: Sep 2014
Location: Oakley, Ca.
Posts: 1,833
Default

Quote:
Originally Posted by Lane_H View Post
I also need to do the same on my 1st build which coincidentally is also a ak63d kit with a fixed rear trunnion.

I am sure the 2nd go round on yours will turn out much nicer..

please ~Splain more bout that front trunnion rivet hole drill method?

hard to see in the pic / not quite sure what sorta clamp/vise is holding your trunnion that allows the receiver to slide into position for drilling.
??
So, couldn't find the time to get to the garage today for better pics, but it's fairly simple how I fixture it up.

Clamp trunnion ears in vice (front to back on top of trunnion)

Lower drill bit into rivet holes, hold down the chuck so the bit stays put through both front holes, and make adjustments as necessary. Clamp vice to table of drill press so everything stays put. Raise the quill (chuck assembly) of the drill press.

Slide receiver over trunnion, check that it is flush with the front of the trunnion, and grab a C-clamp to place around receiver to prevent it moving around.

Drip a few drops of oil on bit, drill through top hole. Drip a bit of oil inside trunnion at other side that will be drilled. Drill all the way through.

Undo clamp around receiver, slide receiver off, deburr holes. Wipe off excess oil to see what you are doing.

Loosen huge C-clamp, and reposition the trunnion for the next hole, and repeat.

Since I started doing it this way my holes are much nicer, and I rarely have to make any adjustment before riveting. A simple deburr is usually sufficient prepwork for riveting.
__________________
Don't sweat the petty things and don't pet the sweaty things.
Lingwendil is online now   Reply With Quote
Old 07-18-2017, 11:42 AM   #11
euroking99
Member
 
AKaholic #: 15327
Join Date: Sep 2008
Location: Thousand Palms, CA
Posts: 384
Default

Who makes this steel ar lower and is it available in 80%?
euroking99 is online now   Reply With Quote
Old 07-18-2017, 11:57 AM   #12
Lane_H
Non-hispanic, Caucasian
 
Lane_H's Avatar
 
AKaholic #: 182543
Join Date: Oct 2015
Location: Ala-F'n-bama
Posts: 2,899
Default

Quote:
Originally Posted by euroking99 View Post
Who makes this steel ar lower and is it available in 80%?
I think it was a joke..

but they do exist
-- http://www.theflatspot.net/ar-15-receiver-flat.html
__________________
Arguing with a man who has renounced his reason is like giving medicine to the dead.
Lane_H is online now   Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump


All times are GMT -4. The time now is 08:46 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2017, vBulletin Solutions, Inc.
©1998-2017 The AK FIles