HOW TO REGISTER AND GET APPROVED FOR THE FORUM

jeremiahwillis · 09-26-2017, 08:40 PM

I too would be interested in an update on the expected date on the 15rd 54R Vepr mags.

Porsche914ls6 · 11-22-2017, 08:05 AM

Me too... can't wait to buy one and immediately modify it to work in my PSL's.

ClayC · 11-22-2017, 01:10 PM

Quote:

Originally Posted by Porsche914ls6

Me too... can't wait to buy one and immediately modify it to work in my PSL's.

so how difficult do you think that will be since the Vepr mag is single stack and the PSL mags are double?

Cyklopz · 01-02-2018, 10:11 PM

2018 hope that 15 round mags make it to production!

**csspecs** · 01-02-2018, 10:51 PM

I'm still waiting on springs.. Should be here in a couple weeks.

josey088 · 01-04-2018, 06:07 PM

Quote:

Originally Posted by ddnc

Here is an idea for some of you that have access to the resources like a 3D printer. Can anyone fabricate a base pad/ end cap for these mags made of polymer or hard rubber?
Although these mags are excellent and the best option in this caliber they are pretty sharp along that bottom edge.
I will buy them if some one can make one that reasonably works and doesn't look odd.

Well, it seems that I am not the only one that want a 54r magazine base plate made from polymer or hard rubber ...
These mags are good , but are very sharp on the bottom edge and would damage any surface that you will put the rifle on , and also the hand if one is not careful while pushing it to seat correctly on the gun . I have personally cut the palm of my hand twice pushing the mags in , already . Nothing serious , but painful .
Hope that Csspecs will listen to customers and make a polymer baseplate that would solve that problem .
I would buy more of those mags if that baseplate is added .

ddnc · 01-04-2018, 08:32 PM

Quote:

Originally Posted by josey088

Well, it seems that I am not the only one that want a 54r magazine base plate made from polymer or hard rubber ...
These mags are good , but are very sharp on the bottom edge and would damage any surface that you will put the rifle on , and also the hand if one is not careful while pushing it to seat correctly on the gun . I have personally cut the palm of my hand twice pushing the mags in , already . Nothing serious , but painful .
Hope that Csspecs will listen to customers and make a polymer baseplate that would solve that problem .
I would buy more of those mags if that baseplate is added .

A removable rubber end cap or “boot” that just slips over the bottom would be fine with me.

josey088 · 01-04-2018, 10:50 PM

Quote:

Originally Posted by ddnc

A removable rubber end cap or “boot” that just slips over the bottom would be fine with me.

It would be fine with me too .

ncgoober · 01-04-2018, 11:14 PM

Cellophane the bottom and then 7$ quart of Plasti-dip? The wrap maybe would maybe even allow the cap to be removed?

flakman · 01-05-2018, 08:06 AM

I am ok with magazine the way it is, just 15 round magazine

subcpo · 02-24-2018, 11:26 PM

Does anybody want to get rid of their 5 round'ers? It will help you pay for the 10 rounder's.
Looking to pick 2-4 more of the 5 round ones up.

Hardcore54r · 06-12-2018, 06:44 AM

Any news...

TheRussian · 06-13-2018, 07:21 PM

My 10 rounders have all worked very well!

frtalbert · 07-04-2018, 08:01 AM

CSS, two questions.

How are the 15 round v54r mags looking?

Are there plans for vepr 6.5 Grendel mags? If so, what kind of ETA are you thinking?

Thanks

Frank

flakman · 07-04-2018, 06:11 PM

Quote:

Originally Posted by frtalbert

CSS, two questions.

How are the 15 round v54r mags looking?

Are there plans for vepr 6.5 Grendel mags? If so, what kind of ETA are you thinking?

Thanks

Frank

they testing 15 round mags, they having some issues and trying to solve them so we could have reliable magazines and per conversation with CSSPECS they working on 6.5 Grendel magazines. its their next project.

aceoutdoor · 11-13-2018, 12:25 AM

Been waiting a long time for these 15rd 54R mags. Csspecs are these looking like they are gonna happen or not? Please update. Thanks

GS455 · 11-13-2018, 12:43 AM

Quote:

Originally Posted by aceoutdoor

Been waiting a long time for these 15rd 54R mags. Csspecs are these looking like they are gonna happen or not? Please update. Thanks

Ever load their 10 rounders? Gonna be tuff pushing 15 rimed cartridges down a single stack banana mag that arcs nearly 90 degrees.

flakman · 11-16-2018, 02:34 PM

Quote:

Originally Posted by aceoutdoor

Been waiting a long time for these 15rd 54R mags. Csspecs are these looking like they are gonna happen or not? Please update. Thanks

go on csspecs website and get their phone number and call them. That would be better way to know

**csspecs** · 11-16-2018, 03:03 PM

Quote:

Originally Posted by aceoutdoor

Been waiting a long time for these 15rd 54R mags. Csspecs are these looking like they are gonna happen or not? Please update. Thanks

The test samples with the larger spring reduced the failures but did not solve it..

I have another possible solution but I need a time slot to do the testing. We need to setup the body tooling, laser cut samples and make the new rear lug parts to test the idea.

Basically I want to test reducing the ramps on the back of the magazine in hopes that it will reduce the time it takes for a round to rise.

Early test sample magazines from before the 10 round magazines came out all worked in 15 round capacity, but they had issues that the ramp parts solved, so we just need to balance the ratio of ramp a little better and hopefully that gets the 15 round magazines running.

I should have time to do a test in the next month or so, if the test result is positive we would go directly to production.

Quote:

Originally Posted by flakman

go on csspecs website and get their phone number and call them. That would be better way to know

Emails or forum questions are prefered.. Getting 40+ phone calls all asking the same thing eats up a lot of my time.

flakman · 11-19-2018, 08:22 AM

Quote:

Originally Posted by csspecs

The test samples with the larger spring reduced the failures but did not solve it..

I have another possible solution but I need a time slot to do the testing. We need to setup the body tooling, laser cut samples and make the new rear lug parts to test the idea.

Basically I want to test reducing the ramps on the back of the magazine in hopes that it will reduce the time it takes for a round to rise.

Early test sample magazines from before the 10 round magazines came out all worked in 15 round capacity, but they had issues that the ramp parts solved, so we just need to balance the ratio of ramp a little better and hopefully that gets the 15 round magazines running.

I should have time to do a test in the next month or so, if the test result is positive we would go directly to production.

Emails or forum questions are prefered.. Getting 40+ phone calls all asking the same thing eats up a lot of my time.

Well agree emails or forum is preferred,

hey I what is status of 6.5x39 Grendel magazines, can't wait for those too

11-22-2017, 08:05 AM	#982
Porsche914ls6 Angry White Trash AKaholic #: 161826 Join Date: Mar 2012 Location: Ice Station Zebra Posts: 8,086	Me too... can't wait to buy one and immediately modify it to work in my PSL's. __________________ I felt a 'fluttering sensation' in my colon...I took a nasty shit..and ...there was don lemon. Licking my turd launcher on the way out and into the porclain gobbler. He had peanuts for eyes...but I recognized him.

01-02-2018, 10:51 PM	#985
csspecs Spam bot Vendor AKaholic #: 157229 Join Date: May 2011 Location: Deland, Florida. Posts: 3,157	I'm still waiting on springs.. Should be here in a couple weeks. __________________ http://stores.csspecs.com/

07-04-2018, 08:01 AM	#994
frtalbert Member AKaholic #: 179226 Join Date: Feb 2015 Location: Lacey, WA Posts: 347	CSS, two questions. How are the 15 round v54r mags looking? Are there plans for vepr 6.5 Grendel mags? If so, what kind of ETA are you thinking? Thanks Frank __________________ r/ Frank

09-26-2017, 08:40 PM	#981
jeremiahwillis Member AKaholic #: 187133 Join Date: Jun 2016 Location: travelers rest, s.c. Posts: 41	I too would be interested in an update on the expected date on the 15rd 54R Vepr mags.

01-02-2018, 10:11 PM	#984
Cyklopz New Member AKaholic #: 186238 Join Date: May 2016 Location: somerset, ky Posts: 10	2018 hope that 15 round mags make it to production!

01-04-2018, 11:14 PM	#989
ncgoober Senior Member AKaholic #: 171030 Join Date: Sep 2013 Location: raleigh,nc Posts: 617	Cellophane the bottom and then 7$ quart of Plasti-dip? The wrap maybe would maybe even allow the cap to be removed?

01-05-2018, 08:06 AM	#990
flakman Senior Member AKaholic #: 190767 Join Date: Dec 2016 Location: Davie, FL Posts: 749	I am ok with magazine the way it is, just 15 round magazine

02-24-2018, 11:26 PM	#991
subcpo Veteran Member Bronze Contributor AKaholic #: 195602 Join Date: Feb 2018 Location: Roll Tide! Posts: 1,010	Does anybody want to get rid of their 5 round'ers? It will help you pay for the 10 rounder's. Looking to pick 2-4 more of the 5 round ones up.

06-12-2018, 06:44 AM	#992
Hardcore54r New Member AKaholic #: 185262 Join Date: Mar 2016 Location: Kodak TN Posts: 7	Any news...

06-13-2018, 07:21 PM	#993
TheRussian Member AKaholic #: 167839 Join Date: Feb 2013 Location: Valhalla Posts: 487	My 10 rounders have all worked very well!

11-13-2018, 12:25 AM	#996
aceoutdoor Member AKaholic #: 162084 Join Date: Apr 2012 Location: In the sticks Posts: 33	Been waiting a long time for these 15rd 54R mags. Csspecs are these looking like they are gonna happen or not? Please update. Thanks

Currently Active Users Viewing This Thread: 3 (0 members and 3 guests)